HEPA Filters
DEEP PLEAT HEPA FILTERS H10 - H13 »
SPECIFICATIONS & OPTIONS
- H10 to H13 Rating
- MDF or Galvanised casing
- Kraft or aluminium spacers
- Extended area option
- Option 292 mm or 150mm deep
- Performance to EN1822
Applications
Normally used for final filtration applications in clean rooms, computer suites, asbestos removal areas, hospital operating theatres and any site requiring ultra clean conditions.
Construction
The filter media is a water repellent pleated micro-glass fibre paper, each pleat is separated either by a kraft paper or aluminum separator. The completed pleat pack is then bonded into a frame which may be of high density particle board, galvanized mild steel, stainless steel or aluminum. Neoprene gaskets may be fitted to either or both filter faces. By extending the surface area it is possible to increase the flow rate for a given size of filter. Approximately twice the flow rate may be achieved through the same size of HEPA filter by extending the surface area – this is accompanied by a slight increase is pressure drop. Face grilles are available as an option.
Performance
Filter medias are DOP tested to guarantee the efficiency at retaining particles of a specific size (0.3 microns). Our HEPA filters are rated at the percentage efficiency of removing 0.3 micron particles and we offer ratings of between 95 and 99.997%. All HEPA filters that we supply are 100% scanned for leak detection to ensure that the filters perform to the stated specification Test Certificates are available on request.
MULTI WEDGE HEPA FILTERS H13 »
- Air flow rate cu.m/h 4000 (Glass) 592x592x292 H13 5150 ( PP)
- Choice of galvanised or HD Styrene case
- Choice of micro-glass or composite media
- Initial pressure loss 250 Pa (Glass) 180 Pa (PP)
- Recommended change out 600 Pa
- Max working temp 60 deg C
Application
Designed for air intake and extract systems of critical applications where high efficiency filtration is necessary. The multi-wedge system provides a much larger media area for higher airflow capacity than standard deep pleat HEPA filters. These filters are subjected to full quality assurance procedures and each filter is individually leak tested, certified and numbered for tracking.
Construction
Manufactured from non fibre-shedding micro-fibre paper or polypropylene composite media the filter packs are mini pleated with the pleats separated by a continuous thermoplastic cord. The filter packs are then sealed with Polyurethane sealant into a galvanized steel or MDF case. The are then fitted with gaskets as required.
Range
Multi-wedge HEPA’s are available with efficiency of H13, in a range of standard cases with nominal airflow rates up to 4000m3/hr.
Performance
Compliant to EN1822 – Most penetrating particle size (approx. 0.12 microns)
RIGID POCKET BAG FILTERS F6 - H10 »
- Choice of media micro-glass or synthetic
- Choice of three standard sizes
- Choice of 20mm header (standard) or 25mm.
- High flow capacity with low pressure loss
- Fully incinerable with no toxic emissions
The rigid bag filters represent a considerable technological innovation in comparison with traditional bag filters. These filters can present many advantages when used as first installation or as replacements to traditional bag filters. The RP filters, with expanded cellular polypropylene pressed frame, are incinerable without releasing toxins.
Performance ratings are in accordance to EN779-2002 Classifications F6 – F9. This gives performance rated at an average of 0.4 micron particle size with efficiencies in the range 60 to +95%
Polyhedral mini-pleat absolute rated HEPA filters with either synthetic media or glass fibre paper media permanently bonded into a plastic carrier frame with two component cold molded polyurethane. The mini pleats are separated by cotton threads hot melt glued into position. Maximum operating temperature 80 deg. C at 100% RH. The filter may be incinerated without emission of toxic gases.
RIGID POCKET BAG FILTERS F6 - H10 »
- Choice of media micro-glass or synthetic
- Choice of three standard sizes
- Choice of 20mm header (standard) or 25mm.
- High flow capacity with low pressure loss
- Fully incinerable with no toxic emissions
The rigid bag filters represent a considerable technological innovation in comparison with traditional bag filters. These filters can present many advantages when used as first installation or as replacements to traditional bag filters. The RP filters, with expanded cellular polypropylene pressed frame, are incinerable without releasing toxins.
Performance ratings are in accordance to EN779-2002 Classifications F6 – F9. This gives performance rated at an average of 0.4 micron particle size with efficiencies in the range 60 to +95%
Polyhedral mini-pleat absolute rated HEPA filters with either synthetic media or glass fibre paper media permanently bonded into a plastic carrier frame with two component cold molded polyurethane. The mini pleats are separated by cotton threads hot melt glued into position. Maximum operating temperature 80 deg. C at 100% RH. The filter may be incinerated without emission of toxic gases.